Search results

Mine did this, I over turned the low speed control and the motor filled with fuel. I had to take the plugs out to get the motor to crank thus blowing the fuel everywhere.

I have spark, no fuel.....

I took the plugs out and it was full but not with water but fuel. After the carb rebuild I used my fingers to adjust the low speed controls and did not get them all the way clock wise before the 1 1/4 turn back. Today I used a screw driver the reset them, they were only about 4-5 turns out. I...

took the sp to the lake to make sure I had a ski to ride this weekend in case the xp carb rebuild did not go well. And as luck would have it the xp ran 2 mins then it shut down. Got the sp out on the lake and as normal it ran great for about 10 mins then it would just stop and shut down...

I just rebuilt Carbs on the 951, had to have the seadoo dealership tighten the rear nut on the exhaust cone ( i could not get a tool over it $10 to tighten) I took it to the lake got into the water started great first crank. Started across the lake hit 7000 plus running great then bogged...

UPdate. The fuel line was dry; I blew compressed air (mouth) on the gas tank and blew the air out of the lines and gas soon followed. Now seems to run ok but idols at around 1200 rpms on the trailer. I used the same springs on the rebuild and did not change the needles or seats. Just...

I ordered the OME rebuild carb kits for my xp limited. I did the rebuild cleaned everything shinny new also replaced all the Tempo fuel lines. Now that everything is back together it will not start, pulled the plugs and they are dry. NO fuel is getting through the carbs. Do I need to prime the...

I have the same ski and nothing but problems. I have a 94sp runs like a charm, the wife has a Kaw and never an issue. I like you have more issues than time to fix them. Good luck I hope you find get it fixe, they sure are great when running...

Is this the correct size for a 951 in a 98 XP Limited? THIS IS A BRAND NEW CARBURETOR REBUILD KIT FOR ALL SUPER BNI MIKUNI 46 MM AND THIS KIT WILL ONLY WORK ON SEADOO'S 951-947 MOTORS, YAMAHA GP800R/1200R POWER VALVE MOTORS WITH BNI CARBS

I have found a few online but wanterd to see if any of the members would recommend a site ect. Also, where do I get the fuel line 20' needed to replace the Tempo stuff? Auto Zone? thanks Do I need the 46MM size kit?

So what you are saying is if you are careful then a good cleaning will do the trick?

Got her all apart and going to replace the lines, the last owner has the plastic pull ties instead of clamps and most are really loose. The ski has Tempo J1527 lines am I correct in thinking these are the bad and need to be replaced ones? I recall reading 25 feet should do it. Any idea what the...

Mr. Honda, maybe I have been working on cars to long, but how can Carbs exist breathing dirty air? This Flame arrestor at least the one that I have seems useless, why have anything there at all? Riverdog, I am trying to get into my head what you are talking about but cant seem to get my head...

If you have a picture of a flame arrestor from a 98 xp limited please email it to me. I purchased a ski and something does not look right. I need to see a picture of another one. I am just not sure if I have the proper one installed on this ski. I just got the ski and now I am having issues...

why is it called flame arrestor? I have a 98 xp limited and the alame arrestor stays unlatched. It only has one latch on the top, I latch it down and it is open before I have gone 1000 feet. In fact it has been running unlatched for the 8 hours that I have had it on the lake since I purchased it...

The issue is getting to the carbs. This thing has ran like a champ all year, now today in the water when I get to about 30 it bogs down then when fuel gets built back into the system it will go like no problems until it burns the fuel build into the system. If I go about 1/2 throttle there is...

The hex screw that holds the throttle lever in place came out, when attempting to put back in it just turns in the hole and will not thread into the handle bar. There does not seem to be threads in the bar to screw into. I did notice that a nut fell out onto the ground, I cant imagine how you...

I took the entire valve out including the rubber o rings, cleaned everything with detergent and water. The valve its self I used carb cleaner and a wire cleaning wheel to clean them (new) shinny clean. One of mine had the o ring in the wrong spot, it apparently was serviced and not put back...

This last weekend my wife and I took our (new to us) skis out. My wife Kaw 900, I have 98 xp limited and we bought my mom a 94 sp. My mom has never been on any lake before she is 70 years old and wanted to try riding a jet ski. Well she loved it in fact it was all we could do to get her home. I...

on my xp limited the oil sending switch connector sometimes gets condensation on the connector, the reading oil amount is correct but it will beep and the light will come on. I then pull the hood open unplug the wire wipe the condensation off the connector and all is good. Also, my lanyard...