Search results

Shits crazy. The old man was calm and slowly walked over there while the others ran for cover. Lol

Ya. I see where you are coming from sportster, makes sense. My plan was to just swap over the accel pump nozzle but the nozzle broke on me when I tried to remove it. Didnt want to chance it on the only good carb I had left because if that one were to break I would be right back in the same boat...

As far as the runaway on the trailer. I have experienced a couple of them, guess I would have to prepare to shock the shit out of myself and pull the plug wires. Maybe keep a thick insulated glove close by. But honestly I have only experienced runaway when I give it throttle while running on the...

Ok thanks guys. I would perfer to keep choke plates installed, but the carbs I ordered had them already removed. So I am going to eliminate choke plates for now. Is it a must to install a primer kit? I live in south texas so it is always warm weather and plus I have accel pump to richen the...

Do I need to rejet if I remove choke plates? Bought a set of carbs for 951 without choke plates. Will stock jets suffice or will I need to rejet? Thanks

Ya sorry. The accel pump nozzle. Dont kno y I said needle jet

Well guys I finally broke down and ordered a set of carbs that need rebuild for 90 bucks. Best deal I could find and good price for both carbs with accel pump. Sportster, I did seee those needle jets on ebay but not sure if they would of worked. So I will just rebuild these carbs and try to...

A little bit too much than what I have to spend right now. My carbs are in decent shape, thats why I am just trying to find this nozzle. But buying a carb might b my only option. Bump for anyone out here with a junk sbn carb laying around. Has to b someone.

No luck with niche cycle. I cleaned jet with carb cleaner and naptha last night. Went to blow compressed air thru it and it shot out of my hand and into my backyard. Lol. Dumbass. Couldnt find it so now I am going to have to replace it. Cant believe this little nozzle is being such a headache...

Lol. Ill try that. I soaked it all night in a bucket of carb cleaner with no luck. The prevoius owner eliminated accel pump and left nozzles uncapped so no telling what is stopping it up.

The pump works fine. It's the nozzle that sticks into the throat of the carb that is clogged up so bad that I cannot get it cleaned.

Any one kno where I can find an accel pump nozzle for sbn carb? Cant find one anywhere. Starting to think it is an obselete part. If anyone out there has any idea where I can find one or an extra set of carbs laying around for parts let me kno. I am refering to the long nozzle that sticks into...

Yes they are both squirting a pretty good stream down the throat of the carb. They are in sync. I will check if the choke helps anything tomorrow when i get out of work and let you kno

Accel pump is good. Rave valves are freshly rebuilt.if the clearance is a little off on raves will it cause the bog I am experiencing? I didnt measure them when I shaved them for the 1mm overbore. I just intalled them into the cylinders and shaved them until I couldnt c them protruding into the...

Ok ive been to hell and back with this ski. Its a 99 gsx ltd. Completely rebuilt motor. 1mm overbore. Stock jetting. Fresh carb rebuild. New fuel lines, cleaned tank and selector valve. Runs great on top end but has a slight hesitation if you crack the throttle from idle. Tried adjusting low...

Thanks bud. Just what I was looking for. Thanks

Sorry. Pulse line. Damn. The fitting on the lower crankcase half right behind the pulse line fitting. Sorry bout that

Finally dropping in freshly built 951. Cant remember what line connects to the 90° fitting right next to the purge line fitting. Please help. Trying to get on water for break in tomorrow morning. Thanks

Badass. Thanks guys. Will let yall know how she runs when I get her together. Crank should be here wednesday. Then its assholes and elbows to try and get it on the water for break in sat morning.

I appreciate everyone's advice. I just ordered a rebuilt crank with 1 year warranty for 300 plus core. I have experience with building motors but this is a first to tear down a jet ski. I'm not used to working with cranks with ball bearings. I'm used to just removing crank and connecting rods...