Search results

My PTO came loose at lake, I am thinking about pulling plugs out and putting 1/4 rope in PTO side cylinder and hand turn PTO to TDC, and hand tight PTO or pipe wrench on shaft or PTO hub, than start and Rev up, dump back in lake and raise it to a plane, this gs has no room for my torque driver...

2001 gs 717 standard carburetor I have a standard single carburetor, is it the higher the spring gram weight, increases pop off pressure, or vice versa

01 gs 717 standard single carb Would it be OK, to remove high and low speed screw jets and spray carb cleaner inside and blow air inside, while still on intake, don't have extra gasket

2001gs 717 My ski will idle in water fine just with flame arrestor on, but when give it throttle it dies, is it getting to much air with air box off, I have trouble with starting, with air box on, I have new carb rebuild, pop off on spec, high speed all the way in low speed 1 1/4 out, how can I...

2001gs717 How do I test ignition coil, in and out of ski, and are the leads going to plugs called secondary, maybe someone has pic or diagram

2001 gs 717 This ski is really unstable in the water. The smallest of wakes at the lake, when sitting at idle wash over side your side splash guards and fills up trying to get in engine hull. I un boarded ski at dock in 8 feet of water, and it flip to that side 45 degrees and there I go for a...

2001 gs 717 What is the idle rpm speed out of water on hose

2001 gs 717 I think that I am missing something, the piece that goes inside the engine mount guide, for cable oil injection See pic from Manuel, its on right for mount, my cable won't stay in guide with out that part

2001 gs 717 My oil injection spring came off again, shouldn't I be able to reinstall without removing carb, out of the way.

2001 gs 717 single carb rebuilt single stock carb, with correct pop off spec, set high speed all the way in, low speed one out, new fuel lines, good compression and rotary valve in spec, good carb pulse. I have to prime threw carb throat to get to fire up, and it will run fine, I shut down and...

2001gs 717 It always been hard starting, after sitting for weeks, even after a total carb rebuilt. I usually put some primer gas down the the carb throat, after that it's fine as long as I use the ski, but one stupid question, should I been be pulling choke after putting in primer gas

717 gs 2001 Is it safe to put a SBT carburetor primer kit, on ski while it's still mounted on ski

01 gs 717 Can I use plastic tubing 1/4 inch for carb pulse line, and fuel line, it is rated for fluid such as acid

2000 seadoo gs 717 My oil injection spring, came off again, last time remove carb, to fix spring, Should I be able to fix spring without removing carb, maybe using wrong tool

I have 2000 gs 717, and have water leaking around one of my head bolt, when it's on the hose. I was thinking about removing bolt and filling hole with sealant,than put bolt slightly threw hole, and let dry than push in further than tighten

I been having trouble trying to start my 01 717 with air box on, it run fine with just flame aristor, so I just wanted to see what's going on, so I put it on the hose and just put air box on, no flame aristor, and put cover on, forgot to latch down, and fired it up, it blew the cover off, it was...

I just completed a long total rebuilt on a 717 gs, going to lake Saturday for 1st run. I have some concerns about the oil injection system working correct. I have med range octane in the tank, I was thinking about adding a little 2 stroke oil to the gas, to be on safe side. Than I do not want to...

I recently bought a new ignition coil on Amazon, well that did not work out, bad coil. I wish that I new a more reliable source

I looking for a source for a RV cover other than SBT, not sure if allowed to post thread

I did not do this procedure, heating flywheel and ring gear with loctite 648 on my 2000 gs 717, no wonder having starting problems with ignition timing. What position should ring be in set inside flywheel